WARFET AEG CONTROL SYSTEM 1.1 GATE (G-WAF)

WARFET aeg control system 1.1


WARFET is the most advanced AEG control system, has 20 functions and almost 6 million possible configurations, the extraordinary tactical programming card makes accessing the WARFET Power Module settings extremely easy, thanks to the Pre- cocking and Smart Trigger, you will get the trigger reaction almost identical to firearms, the programmable Burst allows you to fire a fixed number of shots (1-5 shots) at the same time, which is very useful in MILSLIM and low type magazines -cap, another very useful function is the firing speed adjustment that allows you to reduce the firing speed of your replica in such a way as to use strong LiPo accumulators and nevertheless have ROF as in real weapons, if instead yours replica locks, Smart Fuse protects the battery and engine against failure, also protects the accumulator against excessive discharge.

Features:
Intuitive configuration via the Tactical Programming Card
Robust and super-small size WARFET Power Module
Compatibility with the strongest AEG replicas and batteries (ready to work with LiPo 14.8V, 5000mAh, 60C)
Tested with car batteries
Super-easy installation - thanks to the Mini Tamiya adapters, it is possible to connect to the WARFET (stock) original wiring
It can work with most built-in MOSFETs
With stock of wiring, WARFET reduces melting switch assemblies
In a wired installation, WARFET draws energy from the battery directly to the motor, bypassing the mechanical trigger
Weatherproof (Military Spec: MIL-V-173C)
Deep discharge protection for 7.4V, 11.1V, 14.8V LiPoly and 9.6V, 12.8V LiFePO4
Improve battery reliability, ROF, spring life and gear shift

TACTICAL PROGRAMMING CARD
The unique tactical programming card provides easy access to the Force Module settings. All you have to do is connect the tactical programming card between the battery and the Force Module.

PRE-COCKING
Thanks to the Pre-cocking (Pre-cocking), a trigger reaction similar to a real gun is gained. It allows for initial spring compression, which accelerates the trigger response significantly. Pre-cocking time can be set using the Tactical Programming Card. There are two Pre-cocking modes:
1) AUTO MODE - the spring is automatically compressed after each shot,
2) TRIGGER MODE - the first trigger action compresses the spring, and the second trigger action fires the shot.

PLUG & PLAY
Super-easy installation, just plug and play. No welding required. All you have to do is connect the battery and the rifle to the Force Module.

PROGRAMMABLE BURST
The burst allows you to shoot a predetermined number of BBS (1-5 rounds), which is very useful in MILSLIM and when using low-caps. AUTO MODE can be changed to Burst Mode or Semi Mode to Burst Mode *. The tactical programming card allows you to set the burst time. The Force Module automatically corrects the burst time based on the battery voltage level.

3-round BURST
Burst mode allows you to make a series of 3 shots. This way you can save ammo and increase realism. You can switch from AUTO mode to BURST mode or from SEMI mode to BURST mode.
In SAFE / SEMI / BURST modes, if you release the trigger faster, you can fire one or two. The timing of the burst is set in the menu with an accuracy of 4ms. The processor actively compensates for variations in burst times with a decrease in rate of fire due to battery drain.

CONFIGURABLE FIRE SELECTION
The function that gives you the ability to program the fire selector. There are five modes of operation:
SEMI / AUTO STOCK WIRING
STOCK WIRING SEMI / BURST
MODIFIED WIRING SEMI / AUTO
MODIFIED WIRING SEEDS / BURST
MODIFIED WIRING BURST / AUTO

FIRE CONTROL RATE
It allows the reduction without loss of the rate of fire of the rifle in such a way as to use strong LiPo accumulators and yet have ROF as in real guns.

INTELLIGENT TRIGGER
We know how vital the fast trigger response is during combat. This is why we developed the Smart Trigger function. It enables you to get a quicker activation response.
Works with the ROF control system. During the first shot, the microprocessor sets the ROF control to 100%. After the first shot, it passes to a previously programmed value (for example 50%). As a result, the first shot is fired at a full rate of fire, and subsequent shots at the reduced ROF. The best results are obtained using a battery with a voltage higher than the standard one. For example, if you are using a 7.4V battery, you can replace it with 11.1V. This way, you will get a faster trigger response with the same rate of fire as with a standard battery. In this way, we will get a more responsive trigger with the same rate of fire that you have with a standard battery.

BATTERY PROTECTION
Battery over-discharge protection. Modern LiPo and Vita batteries are very sensitive to over-discharge. If you don't want to damage the battery and are concerned about its service life, this protection is indispensable. The microprocessor monitors the battery voltage constantly. When the voltage drops to a critical level, the controller will not allow cooking.

SMART FUSE
We have created an electronic safety device with precise time measurement. A combination of current, voltage and temperature measurements makes the AEG installation highly reliable. This protects the MOSFET against overheating, overload and short circuit. If your shotgun jams, the SMART fuse protects the motor and battery from damage.

ELECTRONIC FUSE E.
We know how important reliability is on the battlefield. That's why our new MOSFET has thermal protection. In tandem with a time delay fuse, it fully protects the AEG installation.

ACTIVE BRAKE ON / OFF
The Force Module offers the possibility to decide if you want to use the Active Brake function. If you don't need this, you can easily disable it. It will lead to improved engine life.

ACTIVE BRAKE
Don't you care for realism? Do you want to increase the duration of the change? Does your rifle have a high rate of fire that you are unable to make a single shot? Active Brake sets things up. In SEMI mode, the brake does not allow compression of a piston after the shot. The piston stops in the forward position which eliminates unnecessary stress, increasing the life of the reducer and its parts. This is important, especially with an AEG power upgrade. After releasing the trigger, the rifle immediately stops firing. Thus, you gain more realism and also don't waste your precious ammunition.

MOSFET
Do you want to achieve a higher rate of fire and faster trigger response? Are you planning a power upgrade of your rifle? In that case, a MOSFET is required.
It targets the energy from the battery directly to the motor, bypassing the mechanical trigger. As a result, you gain a higher rate of fire from the rifle and a faster trigger response, and the contacts are protected against burn out.

DEBOUNCING
This guarantees full compatibility with microswitches. It guarantees full resistance to contact rebound (vibrations). You gain a larger ROF, a faster trigger response and your MOSFET is less prone to overheating.

BUILT-IN SELF-TEST
Quickly check if the AEG controller is working properly. If you have problems with your AEG, the built-in self-test allows you to verify that the problem is not caused by the controller.

THIRD GENERATION MOSFET
The use of the most modern transistors and microcontrollers allows us to create the smallest and most reliable MOSFET on the market.

MODE DARK
DARK MODE allows you to disable the green LED that lights up when a gun is firing, this feature is especially useful during night games.

COVERING
Thanks to its special coating, it is resistant to atmospheric conditions.

14.8V LI-PO READY
The system can be used with batteries up to 14.8V LI-PO.

HARDWIRED
In the case of a hardwired system, the force module tracks the power from the battery directly to the engine, bypassing the mechanical trigger, this requires a modification of the AEG system.

MINI TAMIYA READY
Tamiya Mini adapters included in the kit, to seamlessly connect AEG Control System for original installation.

QUICKSTART PRINTED
The Quickstart contains basic information and tips.